Browsing Tag

# drone

My name is Ahmad Shamshiri. I am presenting this tutorial from Canada. Hi, Welcome to a video tutorial for Robojax. In this video we are going to review and see this delay timer with display for home automation. As you can time on display, you can
control an AC or DC load to be turned off a certain time and also it has
multiple programming like four different programs.
let’s get started with this. Hardware Explained so this is the module. Here and has a 12
volts relay here and the amount of current is 10 ampere rated either at 30
volts at 10 ampere or 250 volts 10 ampere or 120 volts. 10 ampere multiplied
by the voltage will give you the power that it can control so in these
countries with 250V x 10=2500W if you are in North America
at 120V , then 120V x 10=1205W and so forth. Here we have three
terminals here and three terminal here. There is the positive pin, it will be connected to 12 volts this is the GND and the middle one is
the input or the signal that you can bring it from Arduino or from another
device. There is an opto coupler that isolates this. And also we have a voltage
regulator here of 5 volts. so if you connect here 12 volts all the circuits
inside will work with five volts and that trigger also work works with five
volts. so even if I connect it to 12 that’s
also fine and input will be triggered. We have here three switch with this one you
select which digit you want to change so this one the blank moves from one to the
other one which I’m going to show you next and with this one you can change
the value. Pressing this for long time will change the program mode from
program one program to three and so forth and here we have three pin for the
relay the middle one is a common and this is the normally closed (NC )if you
connect your two wires of the AC load here it will always be connected which
we are not going to use that we are going to use it this way. The middle one
and here and the light is ON the relay will be ON and these two terminal the
two well that you are connected will be connected. The width of this one is 35 mm
thirty five-millimeter the length is 64 millimeters and the depth of the device
is determined by this relay and pin that are sticking out which is 19
millimeter. This module weighs 25.6 grams. Wiring Explained let me explain the AC bulb here. so this
is a table light, this plug is connected to the wall outlet and the wire goes and will be
turned ON, but I have disconnected one of these two wires here I’ve just cut this
wire from here now this can be connected to the relay. Job of the relay is to just
connect it so it will be ON and disconnected it will be OFF. I’ve just
twisted them and then put some solder so this can be inserted into connectors
with a screw. There’s a wiring now. the two wires that I showed you for the AC
ball who will be connected on these two side now it’s disconnected the one that
says what CK and common the matter will not change CK and common so these are
normally open when the relay goes on the light turns ON. these two wires will
be connected. And then on this side there three pins. This connected to 12 volts,
this is connected to the GND of 12 volts this is the trigger which can go
with the 12 volts here. So you can connect and it will work or may be connected
from Arduino or from other source doesn’t matter so the middle one is for
the trigger which receives the signal from any other device that you want to
control this P-1 (Programm 1) this is the zero time as soon as you
trigger or the input gets high voltage and then shuts off then the device stays
ON until the time that you’re set and then it goes OFF. So the trigger time is
very short here I’ve just put it long so you can see it. So it goes ON and it
stays ON for very mom sort moment and then goes OFF. In the graph it was very
short I just showed you so you are not confuse this with something else
else. It goes ON and OFF and then the time stays. here let’s go and set this. This is
the time that I’ve shown there that’s a seven-second was 12 seconds that I
showed in diagram but here I’ve set this because 12 is very long we
press this button and then hold it so it goes to P-1, press it again it goes to
P-2 or 3 and 4 and then it comes back. Once this is in P-1, this
button will not do anything the middle button will make that disappear and then
here we can change the seconds with this button it changed the time so if the
decimal point is here then anything on the left side of decimal point is a
second and on the right side is the decimal point like seven points on one
tenth of a second if the decimal point is here we can move the decimal point or
change the value with these two switches, so if I press this the decimal point disappeared.
Now we have 70 seconds it’s very long let me just show you here so it’s on now
it goes one by one from 70 countdown to zero now when I press this it just stays
on and it blanks now next it goes here and become millisecond so second and
then that would be or one tenth of a second. Now you can set it for very
long period so just push this and that disappeared now with
this one you can select any digit and change it so when I press it this is now
blinking that’s a hundred second it can be changed with this switch I was 370
second so it can go to 999 seconds. If you want to make this
zero just press this update it until it becomes zero and then use this to move
to the next one now this is 70 second. If you want to make it like five second and
at this point make this zero and then go here and then update it five second and
press this and it will disappear so now it’s five seconds. You see that this wire
was removed even if you hold it it will not have any effect. We just need a trigger
(a quick contact) after that it stays there doesn’t do anything because the initial
trigger was important. So my hand just touched it so that was P-1 P-1 (Program 2) when you go to program – it just needs a
trigger. It just triggers and a trigger goes down that then you can set
a time after this time the really will turn ON. from the trigger you can set a
time that relay will turn ON. So let’s say you set for three seconds the trigger
comes, it is OFF for three second and then goes ON for the time that you set.
So in this mode you are setting two times the delay time before it goes ON and the
time that it is ON now let’s set this for press and hold this until you see P
2 and then press this button so the first value is the delay time before the
relay turns ON. To change it we press this button here that dot appears which means
this is a full second if you want to change it to smaller than second with
millisecond just press this again it will come here. So if I press this again it
disappears. Three thing happens either it’s here here or disappears so here
here and disappear. After this if I press this it will go to the next mode.
Let’s changes to just five so it’s here now and with this one you make the blink
come to four and then change it to five after this I’m pressing this and it
moves to the ON mode and the blank is here so you can move the blank to any of
those so let’s just set this to 10 to 10 second, now we have to exit. we
have to press it until the dot disappears.
now with this button, so dot disappears now it’s ready. The five seconds delay
and 10 seconds ON. so when I trigger it and leave so 5 4 3 2 1 and then 10
seconds ON. and then it turns OFF. P-3 (Program 3) there’s no program tree or P-3
has OFF time and ON time. It doesn’t need any trigger as soon as the device is ON it goes OFF and ON and stays ON and then goes OFF stays OFF and so
forth it just continuously going. So you will set two times so the OFF time and
the ON time. when you set the OFF time that light on the device will be off and
when you set that ON time the light will be on OFF. Press this button and then
hold it so it goes to P-1. Press it again it goes to program 2 or P-2.
Just press this metal button now this is the ON time automatically it starts
because it doesn’t need any trigger to change it, press this and now we are in ON and it stays it allows you to change the value.
comes here and now this is the OFF time because this is off this is the off time
so 21 second if you if I change it to be hundred and something so move this. so I’m gonna set it at eight seconds
make this zero. Now that it’s the kind of fact I will press this until the
light is on when the light is on that is the on type so this is on time now move
the blinking with this let’s say make it five seconds five point eight seconds let’s go five point eight and then you
see the off time one point two five point eight on/off on/off continuous
like that P-4 (Program 4) P-4 or program 4 is such that the
trigger happens and stays ON, and from the time that trigger stops the
countdown starts. So if you set it let’s say for 6 seconds when the trigger
stops that time can count down until it’s zero and then the relay will go
disengage or disconnect. So have a look here so now I’m going to P-4
so now I’m in P-4. Plus this so this is 14.7 it with each. So let
me make it smaller to change, now it’s 147 second so let me just change
this to 5 seconds or 6 seconds now disappear. Now look at this, no dot. Nothing. Now when I connect this, it’s on as long as the trigger is ON (or connected)
the relay is ON but when I remove my hand from 6
the countdown starts toward zero. Off now have a look here again this time I’m
gonna disturb (disconnect) it again at the middle of countdown I will connect it and you will
see. so this is ON when I remove it the countdown starts but if I connect this
again the counter resets and it starts from the beginning so , 4, 3, 2
I connect it again it goes back to the set time of 6 seconds and start and then
we’ll countdown until zero. And the relay will turns OFF. this device doesn’t have any
manual they’ve used some kind of translation from Chinese to English and
and after the description this is what they have for this every website every
Chinese website is using this and it seems this has been translated with
Google or some other software from Chinese many of the words that they are
using they don’t make sense if you follow it. So I’m going to publish a
manual for this one so people can download and use. This is a
very useful module for many application with four different programs and time
settings. Definitely it can replace a lot of other devices
I recommend this if you’re using it for time control devices. Thank you for
watching please thumb up 👍 the video please share it and also if you have
any comment or question please post the description below and I will try to
answer and reply Please don’t’ forget to subscribe. This is the least you can do for me. Thank you.

♪ What’s the trick I wish I knew ♪ ♪ I’m so done with thinking through ♪ ♪ All the things I could’ve been ♪ ♪ And I know you wonder too ♪ ♪ All it takes is that one look you do ♪ ♪ And I run right back to you ♪ ♪ You crossed the line ♪ ♪ And it’s time to say F you! ♪ ♪ What’s the point in saying that ♪ ♪ When you know how I’ll react ♪ ♪ You think you can just take it back ♪ ♪ But shit just don’t work like that ♪ ♪ You’re the drug that I’m addicted to ♪ ♪ And I want you so bad ♪ ♪ Guess I’m stuck ♪ ♪ With you ♪ ♪ And that’s that ♪ ♪ Cus when it all falls down,
then whatever ♪ ♪ When it don’t work out for the better ♪ ♪ If we just ain’t right
and it’s time to say goodbye ♪ ♪ When it all falls down ♪ ♪ When it all falls down ♪ ♪ I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ You’re the drug that I’m addicted to ♪ ♪ And I want you so bad ♪ ♪ But I’ll be fine ♪ ♪ Why we fight, I don’t know ♪ ♪ We say what hurts the most ♪ ♪ Oh, I try ♪ ♪ Staying cold ♪ ♪ But you take it personal ♪ ♪ All this firing shots ♪ ♪ And making ground ♪ ♪ It’s way too hard to cope ♪ ♪ But I still ♪ ♪ Can’t let ♪ ♪ You go ♪ ♪ Cus when it all falls down,
then whatever ♪ ♪ When it don’t work out for the better ♪ ♪ If we just ain’t right
and it’s time to say goodbye ♪ ♪ When it all falls down ♪ ♪ When it all falls down ♪ ♪ I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ You’re the drug that I’m addicted to ♪ ♪ And I want you so bad ♪ ♪ But I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ Cus when it all falls down,
then whatever ♪ ♪ When it don’t work out for the better ♪ ♪ If we just ain’t right
and it’s time to say goodbye ♪ ♪ When it all falls down ♪ ♪ When it all falls down ♪ ♪ I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ You’re the drug that I’m addicted to ♪ ♪ And I want you so bad ♪ ♪ But I’ll be fine ♪ ♪ I’ll be fine ♪ ♪ And that’s that ♪

Jet, we’ve got this. It’s time to take this skier down. I’m Victor Muffat-Jeandet, coming from France in
Val d’Isère in the Alps and I’m an alpine ski racer,
more on the technical side, GS and slalom, but also doing
some speed for the combine. My name is Jordan Temkin and I’m a professional drone racer out of Seattle. He takes it! Jet wins it all! Jet is your 2017 World Champion! What do you guys think about the idea of a skier racing a drone? Never thought about that before. That’d be cool. Yeah. A racer versus a drone racer? Uh huh. So, who do you think would win? I would say a drone. The big kicker is the acceleration, right? He’s gotta deal with gravity Where I’m powered. I think I gotta say drone. Zero to 60 in one second. There’s no way you can
go that fast on skis. For sure, the acceleration of the drone is much faster than in skiing,
but now we saw the hill and maybe I can get my
chance as a technical guy. Okay, so would you make
the drone come through and then maybe go through the gates? Okay, there you go, so
that’s what you would do, is make them go through the gates. Maybe even make it one,
two, like croquet. Then, I think the skier would win. Did it? I think it’s gonna
be pretty hard for me, you know, he professionally goes down that kind of hill every day. I don’t. I think the drone will
have to be really precise so it could be close. That guy is such an awesome
skier, I’d probably have to say, he probably could take it. Um, I think the drone would win. I’m hoping for the skier,
that’s really weird for me to say too, as a snowboarder. Oh, the drone’s gonna win. That’s, come on. Science. Science, man. Red course, ready? Blue course, ready? Three, two, one. Go!

Hubsan X4 H501S 57 Flight Gps Brusheless motors 4-25-18 I got this at Frys electronics.. Thanks for watching please subscribe and hit that like button…… (More Videos to come)

– Come on! Should we be doing this? – I don’t know – Something is wrong. Hey guys! We are not sure we
should even make this video. I posteda video yesterday
and you guys told me that, the Game Master hacked into
the video and we uploaded it, it was totally normal and fine. It was a give away with give
away prizes for you guys and and at some point he hacked in We haven’t seen what the game
master put into the video but we are going to watch it now and I did not wanna take down the video because I’ve give away prizes
for you guys so hopefully you guys watch the video,
a link will be right here. Go watch it until the end
because at the end you can see all 5 of the give away prizes. – OK! We are logging
the computer right now. We have not seen what so ever. – Thank you guys, for being
awesome spies and ninjas and letting us know because we
had no idea when we uploaded that this has had happened. – So everybody said it looks
like in the comment section that it was right around like 5:15 5:20’s, so let’s go right to there right now. – Look what it is for you guys. – OK! So it’s Amazon gift card. You hold it, – Wow – It glitched – That’S from that escape room. – It’s the detective board. – How did it all go? – It all led to this. – It’s led to what? – Zamfan. This is a message for you. – It is a message Zamfan. – I have record for this mission. – See! I knew we hacked into it. – We are super secret ninja spies. – Wait. That’s how we had
to do spy, ninja training. – He thinks we are ninja spies though. That’s when we were underneath the house. – That was the first time we received a secret hidden
message from the game master We didn’t even know it
was the Game Master. It was just GM He hypnotized me? I am not hypnotized still though. You guys let me know if you think that I am still hypnotized. I don’t think I am. – No. – That’s you. – Wow. – Beck? – What? This is so weird. – So you went zone out just for a second. – No. I am just thinking. This is crazy. – Let’s go back. Towards the end. – Aa. That was the secret meeting
we had with Project Zorgo. – What do you mean? – He was using it to trap Project Zorgo. – Wait. The Game Master said that the project Zorgo is not the
biggest threat to Youtube So there is someone else. Do you think that has
something to do with Phase 3? – This is starting to get a little weird. – You are just a pawn in a bigger plan. – We saw that. – The Game Master was
Santa’s little helper. We did a face reveal. Wait. What is that, you guys? Looks like. – Wow. Wow. – So there is still unseen footage on here that you guys are first to see it now. We are seeing it. Go back. Wait – What was that? – What was it? You guys let us know what you think it is. Let’s see. What is that? Wait. Is that like a
abandoned room or something? It looks like there is a suitcase there. – Looks like there are two
suitcases. Like put together. – Look. That’s a clock.
It is almost like 3 AM. – This is so weird. What is this even? – Do you guys think.. It’s like a tunnel, a passage
way or something. What? What do you guys think that is?
It looks like a tunnel to me Looks like a safe – Let us know comment section down below what you think these 3 images are? – Yeah. We’ll put them up right here but go check out the video also – What do they all have
to do with each other? – I have no idea but I think this is a clue for Phase 3. What’s gonna happen in 2019. I am nervous. Wow. O my God. ¬ Is that all of your – All of the prizes until the last one. You guys go on to the video
and watch until the end so you can see all the give away prizes. And again I am keeping the video up because I want you to be entered? So if you wanna be
entered in that give away You just have to subscribe
Matt Rebecca Channel, mine Thumbs up both the videos and you can comment on this video or mine The best way to contact
to on social media and which of that 5 items
you would like to win. We’ll pick the winners next week. – What is just going on? – I don’t know. I think next thing we need to do is look at the Game Masters Youtube video. OK, it is the real Game Master. Oh Look! Here is hundred
and 65 thousand subscribers. – Wow – What? Let’s go to the video. Title of this is Phase 3 has begun. New clues and Mystery
Riddles of Stephen Sharer. Stephen shearer. Wait a second. I’ve seen Stephen Sharer’s
Lamborghini. The toy Lamborghini – The Sharergini? – Yeah. You guys,
remember when we went and broke into Stephen Sharer’s
house, the Game Master sinister We found all these clues that made Stephen Sharer
look kind of suspicious. – Yeah. Even that microphone changes your voice to
the Game Master’s voice. – Exactly. SO wWe brought that.We have finger prints If you guys want us to test
the finger prints on the shirt, give us thumbs up right now. Maybe we’ll do after this. I don’t know you guys. Let
us know what you think. If you think we should test it. Wait a sec. We should
subscribe to the channel so we can get notifications
when the Game Master posts. – Why would we do that? – I don’t know. Just in case
so we know a video comes out. – Information. – The only way we know
is when they tell us. – There is an update. The Game Master network begun Phase 3. Secret Ninja spies. The Rebecca’s – Wait. We are not working
for the Game Master. We never said we are working for him. Wow. Matt. What just happened? Do you guys see that? We can’t see the video. – The video turned off. – OK. Hold on. I am gonna
try to pull it up again. – It’s not working. It’s not pulling up anymore. Channel is not there anymore. – Hold on. A message from the Game Master. – What? – For Phase 3 you no longer
the Game Master’s channel. We can’t see any videos? Wait. Is this part of the spy
ninja training for phase 3? The Game Master is making it
harder on us to solve clues. – Why would he do this?
That doesn’t make any sense. Hold on. – We are supposed to be
working for the Game Master. Then why? – I just got another from GM It says only your Zamfam will have access. – The only way we can watch the videos is by you guys telling us
what is in the videos? So we are not able to see it? Wait. Let me check my phone. – Yeah. Check your phone, check your phone – Is it working on your phone? Hold on. – Video. Game Master. It’s not showing up either. I don’t have on mine. I’ve been completely blocked
from the whole channel. – We both are blocked from the channel. It means you guys are the
only ones that can see it. – Since we don’t have access
anymore we need your help. We need the Zamfam folk to figure out exactly what’s going on
with the Game Master. He’s gonna leave clues on that channel. – And we need to stay one step ahead. So you guys make sure
you check the channel. We’ll link it below. If you guys can see anything
just keep us updated. If he posts any new videos because obviously now that we started
Phase 3 we can’t see anything. – I’m gonna put this computer away. Hope you guys thumbs up this video cause I think we need to figure out exactly what’s going on with Stephen Sharergini. – And do the finger prints? Absolutely Oh my Gosh. it is so crazy. I am so nervous for Phase 3 right now. – Here is the Sharergini. So we kept it in a zip lock bag so that our finger prints won’t go on it. – We are actually gonna use an app that we use with fingerprints
off of your Iphone I think where he is gonna
have the most finger prints is gonna be right here. – Right on the Sharer logo. – Right on Sharer logo. I got one. – Definitely finger prints – Wooo. You could see that. – Alright let’s see. – Allows us to figure exactly who it is. – Scanning. Perfect. We put this right down here so that we can save for that later. Alright. It’s a match. Looks like it’s a match
exactly for Stephen Sharer. Obviously we were very
correct figuring out that this finger print was gonna be up here. – Hold. What does tell us about the Game Master’s master plan? – We have to look at something else. Let me grab it. This is the glove the Game
Master have in the Hawaii trip Remember, he left it on the balcony. – Oh my God. – I kept it in a plastic
bag in just the case we need to use it for finger prints. Very carefully grab
this glove out of here. – OK – Put it down right here – I am holding only in this side guys. – Here we go. – If this is a match, Does that mean Stephen Sharer
might be the Game Master? – Look at that.Can you
see that right there? Solid finger prints out of there. As you know there is very
good finger print scan. It is a match again.. Last time it matched both for
Stephen and Chad Wild Clay. This time it’s just
matching Stephen Sharer. – What if this isn’t Game Master’s glove. What if it’s just a normal glove? – But we found this in Hawaii. Remember? It’s from the balcony. Why would Stephen Sharer
have been in Hawaii? He never told us he was going there. There must be something in Hawaii then? Maybe there is another Game
Master’s Headquarter there. – We know the Game Master has
been following Stephen Sharer. Almost everyone of Stephen Sharer’s videos has the Game Master in it. – Let us know you guys think
about the finger prints on the Sharergini matching the fingerprints on the black glove. I thought Stephen might be the Game Master then I thought he might be
working with the Game Master. But the Game Master did say there is a bigger threat, bigger than Project Zorgo .
That’s a threat for Youtube. And I think that might have
something to do with it. I think that the Game Master has been like recruiting
people to work with him. We know that he had a secret
meeting with Grace Sharer too. And he like told her a
bunch of secret information. – I think the Game Master is trying to get us to be ninja spies for him. But I am not, we are not necessarily working with the Game Master. We are just trying to figure it out. – One thing we haven’t opened up yet. This is the one thing that We actually took from Stephen
besides the Sharergini. We took this through the master tunnel. The only reason we took it
because it has this on it. Yeah. – And why was it at
Stephen Sharer’s house? And why was shoved it in his front door and why wouldn’t he tell us? – Give us the thumbs up if you think that we should open this. I forgot about the box to be honest. Why didn’t we open it up sooner? I guess we just had to figure out – Exactly. Let’s go. 3, 2, 1 Whaaat? what? That’s the mask? As seen as Santa’s little helper. That’s the disguise. – Why would that be in here? I thought The Game Master was Santa’s little helper. – Do we wear this one? What is it for? Let us know why you think that this would be in a gift for us? Why would he be giving this? Is this like some weird unboxing … OK. What else is in there? What? It is Chad Wild Clay. – The QWAINT is in there too. Wait. I recognize those. That’s from the detective board Matt. That’s impossible though. Because we haven’t opened the box before we went into that escape room. What else is in there? – This looks like some sort
of blueprint or something. A person here. The world.
Like it goes in from one side and comes out the other. And just like this little
circle thing here too. OK. I have no idea what that means. I think that’s something to do with Phase 3 though Matt. It has to be the Phase 3 hasn’t started means we are leading up to it. – Hold on. Hold on. What’s it now? Insert this to initiate Phase 3. It could be a trap. Last time we inserted something, the video got glitched – Yeah, it had. Look. There is something else in here. All these things are in are in this. So what am I supposed to insert? Hold on. Hold on. Look at it. what? – There is a compartment ain the top. No way. No! Way! What? – It is another SD card It’s a mini SD card. – I think it is technically
called a micro SD card. So where are we supposed to insert this? I don’t know Matt, as
soon as we insert it, It says Phase 3 will be initiated. – Phase 3 is actually good.
It is trying to take down a bigger threat than Project Zorgo. I don’t know if we wanna be a part of it. – If its for good, I think
we should be a part of this. We still don’t know for sure, if the Game Master is good. He has done a lot of good things but I don’t know if we could trust him? – Let us now at the comment
section down below if you think we should insert this in? I don’t know. What should we put this in? Hold on. What? – Don’t we have the device? Device we got in the mystery box? – Yeah. that they left at our front door? – Do we still have it? Here it is. Here it is. What do you think this is? It says AABO. – It might be a 4 digit code
of some sort that we use later. I don’t know – Here. We are up here. It says TF. – TF? I don’t know what that means. Do you guys know what TF means? – So I think we need to do this but … – I know that as soon as
we insert this that means we are starting Phase 3. I don’t know if we should. You guys, what should we
do? Should we insert it? OK. Do you think we should take this mask? It might mean something. What if this mask has
something to do with it. – Here we go. – I am nervous Matt. O my Gosh. – 3, 2, 1.

Set up LEDS on Parrot Bebop 1 Hello, Today on this small video, I wanted to share : 1) how I changed the propellers 2) How to set LEDS on the bottom of the drone I bought everything for 15€ on aliexpress (Link in the description) Regarding the propellers, they come on this small package And for the LEDs, it’s a small electic panel which is connected to the battery via a small adaptator Let’s start with the easiest part. Change the propellers. You should all have this small piece Here is the old one Let’s compare the official with the aliexpress It’s exacly the same exept the price 🙂 It’s harder to fix it. It looks like the official is more flexible than the aliexpress Let’s set the LEDs now Here is the connexion to the battery There is a large choice of blinking mode Unscrew the shock absorbers to place properly the cable be carefull to place the LEDS on the correct side In the package, you will find new screws to fix the LEDS Job DONE 🙂 I can now place the shock absorber screws Cables won’t touch the propellers Let’s fly it !

Kevin: My money should
work as hard as I do. So I use my
Freedom Unlimited card to buy all the
latest tech stuff. Today, I’m earning on a charger. Cashier: So, just
the charger then? Kevin: Um… [bold music] Ahhh… [laughs] [crash!] [drones buzz] Yeah! Cashier: Fantastic! Kevin: Earn 1.5% cash back
on everything you buy with Freedom Unlimited. Chase. Make more
of what’s yours.

Vannes – Bretagne – Morbihan